1. Colorado small cities
2. Colorado smaller cities
3. Colorado
4. Denver County, CO Restaurants

Violation descriptions and comments

Sep 26, 2000

SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.

Feb 22, 2001

IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Jun 20, 2001

SANITATION RINSE
4a Manual
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
When equipment and utensils are washed and sanitized by hand a three basin sink is required. The first basin is filled with hot soapy water. The second is filled with clean rinse water and the third is filled with water containing sanitizer. Equipment and utensils are washed in the first basin to remove all food residue. They are then rinsed free of detergents in the second compartment and are then placed in the third compartment where they are sanitized. The equipment and utensils must remain in the sanitizing solution for at least one minute to allow the sanitizer enough contact time to effectively kill any disease-causing microorganisms that may be left on the surfaces after washing and rinsing.
SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Non-food contact surfaces of equipment routinely exposed to splash or food debris must be constructed to be smooth, durable, nonabsorbent and easily cleanable. Equipment that does not meet these criteria becomes difficult to clean, allowing soil, moisture, debris and disease-causing bacteria to accumulate.

Oct 15, 2001

PHYSICAL FACILITIES
14a Plumbing not installed/maintained
PUBLIC HEALTH SIGNIFICANCE
It is critical that all plumbing fixtures, water and sewer lines in food establishments be maintained in proper working order. Poorly maintained plumbing systems may result in potential heath hazard such as cross connections, the back up of sewage, or leakage. These conditions may directly result in the contamination of food, equipment, utensils or paper goods. They can also adversely affect the ability of food handlers to adequately wash their hands, an establishment’s warewashing operations and increase the potential for cross contamination of food and equipment and utensil.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Feb 8, 2002

PHYSICAL FACILITIES
14a Plumbing not installed/maintained
PUBLIC HEALTH SIGNIFICANCE
It is critical that all plumbing fixtures, water and sewer lines in food establishments be maintained in proper working order. Poorly maintained plumbing systems may result in potential heath hazard such as cross connections, the back up of sewage, or leakage. These conditions may directly result in the contamination of food, equipment, utensils or paper goods. They can also adversely affect the ability of food handlers to adequately wash their hands, an establishment’s warewashing operations and increase the potential for cross contamination of food and equipment and utensil.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Jun 19, 2002

FOOD SOURCE
1c Cross-contamination
PUBLIC HEALTH SIGNIFICANCE
Disease-causing bacteria can be transferred to food from utensils that have been stored on surfaces which have not been cleaned and sanitized. Equipment such as meat grinders can transfer disease-causing bacteria from one animal species to another if not cleaned and sanitized between different species. Some disease-causing microorganisms survive outside the body for considerable periods of time. Food that comes into contact directly or indirectly with surfaces that are not clean and sanitized is liable to such contamination.
FOOD TEMPERATURE CONTROL
3b Rapidly reheat to 165 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
If the food becomes hot enough during cooking, most disease-causing bacteria and viruses will be destroyed. One exception is a type of bacteria that can form heat-resistant spores (an example is Clostridium perfringens.) However, cooked food can become recontaminated after cooking with bacteria from hands, utensils, coughing, sneezing, etc
FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.
PHYSICAL FACILITIES
14a Plumbing not installed/maintained
PUBLIC HEALTH SIGNIFICANCE
It is critical that all plumbing fixtures, water and sewer lines in food establishments be maintained in proper working order. Poorly maintained plumbing systems may result in potential heath hazard such as cross connections, the back up of sewage, or leakage. These conditions may directly result in the contamination of food, equipment, utensils or paper goods. They can also adversely affect the ability of food handlers to adequately wash their hands, an establishment’s warewashing operations and increase the potential for cross contamination of food and equipment and utensil.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Sep 30, 2002

PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Jan 30, 2003

WATER * SEWAGE * PLUMBING SYSTEMS
5c Unprotected backflow, back siphonage
PUBLIC HEALTH SIGNIFICANCE
Plumbing connections between potable or drinking water plumbing systems and non-potable water systems are called cross connections. Cross connections can occur in many different ways in a food establishment. The simplest may be a hose attached to a faucet that is dropped into a container or sink filled with non-potable, contaminated water. In this example there is a direct connection between the building’s potable water system and the contaminated or non-potable water in the container or sink. To prevent the “backflow” of contaminated water back into the building’s water system caused by siphonage, a proper backflow protection device must be installed on the faucet where the hose is attached. Backflow devices must be correctly installed to assure their proper operation and maintenance. Backflow devices must be installed on all faucets or hose bibs where a hose can be attached, on soap and other chemical dispensing systems that are plumbed to the buildings water systems, on water lines to dish machines and in soft drink carbonator systems. To prevent the possibility of sewage contacting food or backing up into fixtures such as food preparation sinks, warewashing sinks, ice bins, refrigerators or dishmachines, the drainage systems from these fixtures must drain through an “air break” before entering the sewer. This physical gap in the drain line does not allow waste water to back up into fixtures if a sewage back up should occur.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
PHYSICAL FACILITIES
14a Plumbing not installed/maintained
PUBLIC HEALTH SIGNIFICANCE
It is critical that all plumbing fixtures, water and sewer lines in food establishments be maintained in proper working order. Poorly maintained plumbing systems may result in potential heath hazard such as cross connections, the back up of sewage, or leakage. These conditions may directly result in the contamination of food, equipment, utensils or paper goods. They can also adversely affect the ability of food handlers to adequately wash their hands, an establishment’s warewashing operations and increase the potential for cross contamination of food and equipment and utensil.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Apr 15, 2003

SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
WATER * SEWAGE * PLUMBING SYSTEMS
5c Unprotected backflow, back siphonage
PUBLIC HEALTH SIGNIFICANCE
Plumbing connections between potable or drinking water plumbing systems and non-potable water systems are called cross connections. Cross connections can occur in many different ways in a food establishment. The simplest may be a hose attached to a faucet that is dropped into a container or sink filled with non-potable, contaminated water. In this example there is a direct connection between the building’s potable water system and the contaminated or non-potable water in the container or sink. To prevent the “backflow” of contaminated water back into the building’s water system caused by siphonage, a proper backflow protection device must be installed on the faucet where the hose is attached. Backflow devices must be correctly installed to assure their proper operation and maintenance. Backflow devices must be installed on all faucets or hose bibs where a hose can be attached, on soap and other chemical dispensing systems that are plumbed to the buildings water systems, on water lines to dish machines and in soft drink carbonator systems. To prevent the possibility of sewage contacting food or backing up into fixtures such as food preparation sinks, warewashing sinks, ice bins, refrigerators or dishmachines, the drainage systems from these fixtures must drain through an “air break” before entering the sewer. This physical gap in the drain line does not allow waste water to back up into fixtures if a sewage back up should occur.
PHYSICAL FACILITIES
14b Garbage and refuse accumulation/uncovered
PUBLIC HEALTH SIGNIFICANCE
The proper storage and disposal of garbage and refuse is necessary to minimize insect, rodent and odor problems. Improperly handled garbage and refuse creates nuisance conditions, makes housekeeping difficult and can result in the contamination of food, equipment and utensils. Garbage and refuse is to be removed form the food establishment daily. It is to be stored in clean, covered, leak proof trash cans, dumpsters or compactors that prevent the scattering of the garbage and refuse by birds. Garbage and refuse must not attract, or harbor or act as a breeding place for flies and rodents. Recyclable materials must be handled in the same manner as garbage and refuse so as to minimize orders, insects and rodents. Recyclable materials, garbage and refuse must be removed from the premises at least once a week.
The proper storage of recyclable materials, garbage and refuse is necessary to minimize insect, rodent and odor problems. Trash dumpster, compactors must be located on concrete or rolled asphalt pads to provide a surface that can be easily cleaned, and that inhibits the breeding of flies and rodents. Floors, walls and ceilings of recycling rooms must be constructed of smooth, durable, non-absorbent materials to facilitate easy cleaning.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.

Apr 29, 2003

WATER * SEWAGE * PLUMBING SYSTEMS
5c Unprotected backflow, back siphonage
PUBLIC HEALTH SIGNIFICANCE
Plumbing connections between potable or drinking water plumbing systems and non-potable water systems are called cross connections. Cross connections can occur in many different ways in a food establishment. The simplest may be a hose attached to a faucet that is dropped into a container or sink filled with non-potable, contaminated water. In this example there is a direct connection between the building’s potable water system and the contaminated or non-potable water in the container or sink. To prevent the “backflow” of contaminated water back into the building’s water system caused by siphonage, a proper backflow protection device must be installed on the faucet where the hose is attached. Backflow devices must be correctly installed to assure their proper operation and maintenance. Backflow devices must be installed on all faucets or hose bibs where a hose can be attached, on soap and other chemical dispensing systems that are plumbed to the buildings water systems, on water lines to dish machines and in soft drink carbonator systems. To prevent the possibility of sewage contacting food or backing up into fixtures such as food preparation sinks, warewashing sinks, ice bins, refrigerators or dishmachines, the drainage systems from these fixtures must drain through an “air break” before entering the sewer. This physical gap in the drain line does not allow waste water to back up into fixtures if a sewage back up should occur.

Sep 6, 2003

TOXIC ITEMS
8a Improperly stored
PUBLIC HEALTH SIGNIFICANCE
Separation of cleaners, sanitizers and other chemicals from food, equipment and utensils helps ensure that chemical contamination does not occur. Cleaners, sanitizers and other chemicals must be stored below and away from all food, food preparation areas, warewashing areas, clean equipment and utensils, paper good and single service items.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.

Jan 2, 2004

IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Oct 5, 2004

FOOD TEMPERATURE CONTROL
3f Food thermometer not available
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Because food temperature control is so critical in assuring food safety all foods establishment must have and must use an accurate thermometer to check food temperatures. Food product thermometers are to be scaled 0—220oF. They must be accurate to +/-2oF. Food workers need to verify that foods are being properly cooled, that they are reheated to 165oF, that they are cooked to the required temperatures, that they are held hot above 140oF, etc. by using a thermometer.

Mar 3, 2005

PERSONNEL
2e Smoking; eating; drinking not restricted
PUBLIC HEALTH SIGNIFICANCE
The use of tobacco products or eating or drinking during food preparation is prohibited. The hand to mouth contact that occurs during these activities results in the contamination of workers hands and food.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Jul 22, 2005

SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
HAND WASHING & TOILET FACILITIES
6b Inaccessible
PUBLIC HEALTH SIGNIFICANCE
Food workers may be unlikely to wash their hands unless properly equipped handwashing sinks are accessible in the immediate work area. Handwashing sinks which are improperly located may be blocked by portable equipment or stacked full of soiled utensils and other items, rendering the sink unavailable for use. Nothing must block the approach to a handwashing sink thereby discouraging its use.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

Dec 29, 2005

IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.
UTENSILS - SINGLE SERVICE ARTICLES
13b Single service articles improperly stored, dispensed, used
PUBLIC HEALTH SIGNIFICANCE
Single service items such as paper cups, napkins, straws, plastic “to-go” food containers and plastic tableware must be stored and dispensed in a manner that protects these items from contamination. Single service items must be stored up off the floor. Dispensers can be used to protect these items when in service. Single service items such as tableware may be prewrapped, or provided in a dispenser that presents the utensil handle to the server or consumer.

May 16, 2006

IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

Oct 20, 2006

TOXIC ITEMS
8a Improperly stored
PUBLIC HEALTH SIGNIFICANCE
Separation of cleaners, sanitizers and other chemicals from food, equipment and utensils helps ensure that chemical contamination does not occur. Cleaners, sanitizers and other chemicals must be stored below and away from all food, food preparation areas, warewashing areas, clean equipment and utensils, paper good and single service items.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Non-food contact surfaces of equipment routinely exposed to splash or food debris must be constructed to be smooth, durable, nonabsorbent and easily cleanable. Equipment that does not meet these criteria becomes difficult to clean, allowing soil, moisture, debris and disease-causing bacteria to accumulate.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.

Feb 21, 2007

FOOD SOURCE
1b Unwholesome; signs of spoilage
PUBLIC HEALTH SIGNIFICANCE
Canned or hermetically sealed foods must be handled so as to maintain container and product integrity. Dented and damaged containers allow for the contamination of the food within the container. This contamination can result in the growth of disease-causing bacteria or spoilage of the can’s contents. Food establishments are required to inspect can goods for damage. Damaged goods are not to be used. They must be disposed of or be segregated and held in designated areas pending proper disposition.

Feb 22, 2007

FOOD SOURCE
1b Unwholesome; signs of spoilage
PUBLIC HEALTH SIGNIFICANCE
Canned or hermetically sealed foods must be handled so as to maintain container and product integrity. Dented and damaged containers allow for the contamination of the food within the container. This contamination can result in the growth of disease-causing bacteria or spoilage of the can’s contents. Food establishments are required to inspect can goods for damage. Damaged goods are not to be used. They must be disposed of or be segregated and held in designated areas pending proper disposition.

Mar 28, 2007

FOOD TEMPERATURE CONTROL
3b Rapidly reheat to 165 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
If the food becomes hot enough during cooking, most disease-causing bacteria and viruses will be destroyed. One exception is a type of bacteria that can form heat-resistant spores (an example is Clostridium perfringens.) However, cooked food can become recontaminated after cooking with bacteria from hands, utensils, coughing, sneezing, etc
SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12d Wiping cloths
PUBLIC HEALTH SIGNIFICANCE
Counter tops, work tables, cutting boards, and other food contact surfaces are required to be wiped down constantly to keep them free of food spill. If spills are left to accumulate, disease-causing microorganisms can survive on contaminated surfaces. Foods, equipment and utensils that come into contact with these dirty surfaces will also become contaminated. To prevent this contamination, wiping cloths must be saturated with a sanitizing solution of adequate strength to kill microorganisms that may be on these surfaces.
UTENSILS - SINGLE SERVICE ARTICLES
13b Single service articles improperly stored, dispensed, used
PUBLIC HEALTH SIGNIFICANCE
Single service items such as paper cups, napkins, straws, plastic “to-go” food containers and plastic tableware must be stored and dispensed in a manner that protects these items from contamination. Single service items must be stored up off the floor. Dispensers can be used to protect these items when in service. Single service items such as tableware may be prewrapped, or provided in a dispenser that presents the utensil handle to the server or consumer.
PHYSICAL FACILITIES
14a Plumbing not installed/maintained
PUBLIC HEALTH SIGNIFICANCE
It is critical that all plumbing fixtures, water and sewer lines in food establishments be maintained in proper working order. Poorly maintained plumbing systems may result in potential heath hazard such as cross connections, the back up of sewage, or leakage. These conditions may directly result in the contamination of food, equipment, utensils or paper goods. They can also adversely affect the ability of food handlers to adequately wash their hands, an establishment’s warewashing operations and increase the potential for cross contamination of food and equipment and utensil.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.

Aug 15, 2007

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD TEMPERATURE CONTROL
3g Equipment inadequate to maintain food temperatures
PUBLIC HEALTH SIGNIFICANCE
The ability of equipment to cool, heat, and hold potentially hazardous foods at required temperatures is critical to food safety. Improper holding and cooking temperatures continue to be major contributing factors to foodborne illness. Therefore, it is very important to have adequate cooking, hot and cold holding equipment with enough capacity to meet the heating and cooling demands of the establishment.
PEST CONTROL
7a Evidence of insects or rodents
PUBLIC HEALTH SIGNIFICANCE
Rodents such as mice and rats live in and feed on garbage and refuse. Disease-causing microorganisms are therefore often present on their hair, in their feces and urine. Microorganisms can be transmitted to people when rodents come into contact and contaminate food and food contact surfaces.
Flies breed in and feed on garbage, refuse and sewage. Disease-causing microorganisms are therefore often present on their body hairs and mouth parts. Microorganisms can be transmitted to people when flies land on and contaminate food and utensils.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Aug 22, 2007

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD TEMPERATURE CONTROL
3g Equipment inadequate to maintain food temperatures
PUBLIC HEALTH SIGNIFICANCE
The ability of equipment to cool, heat, and hold potentially hazardous foods at required temperatures is critical to food safety. Improper holding and cooking temperatures continue to be major contributing factors to foodborne illness. Therefore, it is very important to have adequate cooking, hot and cold holding equipment with enough capacity to meet the heating and cooling demands of the establishment.
PEST CONTROL
7a Evidence of insects or rodents
PUBLIC HEALTH SIGNIFICANCE
Rodents such as mice and rats live in and feed on garbage and refuse. Disease-causing microorganisms are therefore often present on their hair, in their feces and urine. Microorganisms can be transmitted to people when rodents come into contact and contaminate food and food contact surfaces.
Flies breed in and feed on garbage, refuse and sewage. Disease-causing microorganisms are therefore often present on their body hairs and mouth parts. Microorganisms can be transmitted to people when flies land on and contaminate food and utensils.

Jan 25, 2008

FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.
PHYSICAL FACILITIES
14a Plumbing not installed/maintained
PUBLIC HEALTH SIGNIFICANCE
It is critical that all plumbing fixtures, water and sewer lines in food establishments be maintained in proper working order. Poorly maintained plumbing systems may result in potential heath hazard such as cross connections, the back up of sewage, or leakage. These conditions may directly result in the contamination of food, equipment, utensils or paper goods. They can also adversely affect the ability of food handlers to adequately wash their hands, an establishment’s warewashing operations and increase the potential for cross contamination of food and equipment and utensil.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Mar 21, 2008

PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

May 12, 2008

FOOD SOURCE
1c Cross-contamination
PUBLIC HEALTH SIGNIFICANCE
Disease-causing bacteria can be transferred to food from utensils that have been stored on surfaces which have not been cleaned and sanitized. Equipment such as meat grinders can transfer disease-causing bacteria from one animal species to another if not cleaned and sanitized between different species. Some disease-causing microorganisms survive outside the body for considerable periods of time. Food that comes into contact directly or indirectly with surfaces that are not clean and sanitized is liable to such contamination.
TESTING DEVICES
11c Chemical test kits not provided; inaccessible
PUBLIC HEALTH SIGNIFICANCE
The temperature of the wash and rinse water is a critical factor effecting cleaning and sanitizing of equipment and utensils. It is important that warewashing machines and high-temperature three-compartment warewashing sinks are therefore equipped with accurate thermometers to measure water temperatures. Sanitzer test kits must also be provided and used by food workers to ensure that the concentration of any chemical sanitizers being used are correct. Warewashing machines are required to operate at specific water flow pressures. Water flow pressure can greatly effect how well a dishmachine will sanitize. Low water flow pressure results in inadequate spray patterns and incomplete coverage of the equipment and utensils being washed. Excessive flow pressures will atomize water droplets and again result in incomplete coverage. A pressure gauge installed on the dishmachine’s final rinse line allows workers to monitor the water flow pressure of a dishmachine.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.

Oct 15, 2008

FOOD SOURCE
1c Cross-contamination
PUBLIC HEALTH SIGNIFICANCE
Disease-causing bacteria can be transferred to food from utensils that have been stored on surfaces which have not been cleaned and sanitized. Equipment such as meat grinders can transfer disease-causing bacteria from one animal species to another if not cleaned and sanitized between different species. Some disease-causing microorganisms survive outside the body for considerable periods of time. Food that comes into contact directly or indirectly with surfaces that are not clean and sanitized is liable to such contamination.
FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12d Wiping cloths
PUBLIC HEALTH SIGNIFICANCE
Counter tops, work tables, cutting boards, and other food contact surfaces are required to be wiped down constantly to keep them free of food spill. If spills are left to accumulate, disease-causing microorganisms can survive on contaminated surfaces. Foods, equipment and utensils that come into contact with these dirty surfaces will also become contaminated. To prevent this contamination, wiping cloths must be saturated with a sanitizing solution of adequate strength to kill microorganisms that may be on these surfaces.

Feb 6, 2009

FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Non-food contact surfaces of equipment routinely exposed to splash or food debris must be constructed to be smooth, durable, nonabsorbent and easily cleanable. Equipment that does not meet these criteria becomes difficult to clean, allowing soil, moisture, debris and disease-causing bacteria to accumulate.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Jun 25, 2009

IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

Nov 17, 2009

WATER * SEWAGE * PLUMBING SYSTEMS
5d Improper sewage disposal
PUBLIC HEALTH SIGNIFICANCE
Adequate sewage and waste water disposal is a basic requirement for all food operations. All waste water contains high levels of disease-causing micrograms. The improper disposal of waste water is often associated with disease outbreaks. Food establishments must dispose of all waste water into sanitary sewer. Both public or individual waste water treatment (septic) sewerage systems must be maintained to prevent the backup of sewage into the establishment or on to the ground outside.
UTENSILS - SINGLE SERVICE ARTICLES
13b Single service articles improperly stored, dispensed, used
PUBLIC HEALTH SIGNIFICANCE
Single service items such as paper cups, napkins, straws, plastic “to-go” food containers and plastic tableware must be stored and dispensed in a manner that protects these items from contamination. Single service items must be stored up off the floor. Dispensers can be used to protect these items when in service. Single service items such as tableware may be prewrapped, or provided in a dispenser that presents the utensil handle to the server or consumer.

Feb 25, 2010

FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Feb 25, 2011

SANITATION RINSE
4a Manual
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
When equipment and utensils are washed and sanitized by hand a three basin sink is required. The first basin is filled with hot soapy water. The second is filled with clean rinse water and the third is filled with water containing sanitizer. Equipment and utensils are washed in the first basin to remove all food residue. They are then rinsed free of detergents in the second compartment and are then placed in the third compartment where they are sanitized. The equipment and utensils must remain in the sanitizing solution for at least one minute to allow the sanitizer enough contact time to effectively kill any disease-causing microorganisms that may be left on the surfaces after washing and rinsing.
SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12d Wiping cloths
PUBLIC HEALTH SIGNIFICANCE
Counter tops, work tables, cutting boards, and other food contact surfaces are required to be wiped down constantly to keep them free of food spill. If spills are left to accumulate, disease-causing microorganisms can survive on contaminated surfaces. Foods, equipment and utensils that come into contact with these dirty surfaces will also become contaminated. To prevent this contamination, wiping cloths must be saturated with a sanitizing solution of adequate strength to kill microorganisms that may be on these surfaces.

Jul 6, 2011

PERSONNEL
2c Hands not washed as needed
PUBLIC HEALTH SIGNIFICANCE
The hands are particularly important in transmitting foodborne disease-causing organisms. Food employees with dirty hands and/or fingernails may contaminate the food being prepared. Therefore, any activity which may contaminate the hands must be followed by thorough handwashing. Even seemingly healthy employees may serve as reservoirs for disease-causing microorganisms that are transmissible through food. Staphylococci bacteria, for example, can be found on the skin and in the mouth, throat, and nose of many healthy employees. The hands of employees can be contaminated by touching their nose, mouth, hair or other body parts.
PERSONNEL
2d Poor hygienic practices
PUBLIC HEALTH SIGNIFICANCE
Retail food establishments must have a Health Department approved Hazard Analysis Critical Control Point (HACCP) plan in place when vacuum packageing or when conducting other forms of modified oxygen packaging (MAP). Foods not properly processed using MAP techniques are prone to the growth of botulism. All MAP processed foods must be held refrigerated at 41oF or less until cooking or service. Shelf life of MAP foods are not to exceed 10 days.
PERSONNEL
2e Smoking; eating; drinking not restricted
PUBLIC HEALTH SIGNIFICANCE
The use of tobacco products or eating or drinking during food preparation is prohibited. The hand to mouth contact that occurs during these activities results in the contamination of workers hands and food.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
SANITATION RINSE
4a Manual
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
When equipment and utensils are washed and sanitized by hand a three basin sink is required. The first basin is filled with hot soapy water. The second is filled with clean rinse water and the third is filled with water containing sanitizer. Equipment and utensils are washed in the first basin to remove all food residue. They are then rinsed free of detergents in the second compartment and are then placed in the third compartment where they are sanitized. The equipment and utensils must remain in the sanitizing solution for at least one minute to allow the sanitizer enough contact time to effectively kill any disease-causing microorganisms that may be left on the surfaces after washing and rinsing.
WATER * SEWAGE * PLUMBING SYSTEMS
5d Improper sewage disposal
PUBLIC HEALTH SIGNIFICANCE
Adequate sewage and waste water disposal is a basic requirement for all food operations. All waste water contains high levels of disease-causing micrograms. The improper disposal of waste water is often associated with disease outbreaks. Food establishments must dispose of all waste water into sanitary sewer. Both public or individual waste water treatment (septic) sewerage systems must be maintained to prevent the backup of sewage into the establishment or on to the ground outside.
HAND WASHING & TOILET FACILITIES
6b Inaccessible
PUBLIC HEALTH SIGNIFICANCE
Food workers may be unlikely to wash their hands unless properly equipped handwashing sinks are accessible in the immediate work area. Handwashing sinks which are improperly located may be blocked by portable equipment or stacked full of soiled utensils and other items, rendering the sink unavailable for use. Nothing must block the approach to a handwashing sink thereby discouraging its use.
PEST CONTROL
7a Evidence of insects or rodents
PUBLIC HEALTH SIGNIFICANCE
Rodents such as mice and rats live in and feed on garbage and refuse. Disease-causing microorganisms are therefore often present on their hair, in their feces and urine. Microorganisms can be transmitted to people when rodents come into contact and contaminate food and food contact surfaces.
Flies breed in and feed on garbage, refuse and sewage. Disease-causing microorganisms are therefore often present on their body hairs and mouth parts. Microorganisms can be transmitted to people when flies land on and contaminate food and utensils.

Oct 13, 2011

PERSONNEL
2c Hands not washed as needed
PUBLIC HEALTH SIGNIFICANCE
The hands are particularly important in transmitting foodborne disease-causing organisms. Food employees with dirty hands and/or fingernails may contaminate the food being prepared. Therefore, any activity which may contaminate the hands must be followed by thorough handwashing. Even seemingly healthy employees may serve as reservoirs for disease-causing microorganisms that are transmissible through food. Staphylococci bacteria, for example, can be found on the skin and in the mouth, throat, and nose of many healthy employees. The hands of employees can be contaminated by touching their nose, mouth, hair or other body parts.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
TESTING DEVICES
11a Refrigeration units not provided with accurate, conspicuous thermometer
PUBLIC HEALTH SIGNIFICANCE
Conspicuous thermometers are required in all refrigeration units and hot food holding cabinets where potentially hazardous foods are stored. Maintaining foods at safe temperatures is critical in controlling the growth of disease-causing bacteria. Should the temperature of a refrigerator exceed 41oF or a hot holding cabinet be less than 140oF, bacterial growth can occur. In order to facilitate the routine monitoring of equipment temperatures, clearly visible thermometers must be provided in all refrigerations and hot holding cabinets and must be routinely checked by food establishment personnel.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

Oct 21, 2011

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.

Feb 9, 2012

FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
SANITATION RINSE
4a Manual
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
When equipment and utensils are washed and sanitized by hand a three basin sink is required. The first basin is filled with hot soapy water. The second is filled with clean rinse water and the third is filled with water containing sanitizer. Equipment and utensils are washed in the first basin to remove all food residue. They are then rinsed free of detergents in the second compartment and are then placed in the third compartment where they are sanitized. The equipment and utensils must remain in the sanitizing solution for at least one minute to allow the sanitizer enough contact time to effectively kill any disease-causing microorganisms that may be left on the surfaces after washing and rinsing.
WATER * SEWAGE * PLUMBING SYSTEMS
5c Unprotected backflow, back siphonage
PUBLIC HEALTH SIGNIFICANCE
Plumbing connections between potable or drinking water plumbing systems and non-potable water systems are called cross connections. Cross connections can occur in many different ways in a food establishment. The simplest may be a hose attached to a faucet that is dropped into a container or sink filled with non-potable, contaminated water. In this example there is a direct connection between the building’s potable water system and the contaminated or non-potable water in the container or sink. To prevent the “backflow” of contaminated water back into the building’s water system caused by siphonage, a proper backflow protection device must be installed on the faucet where the hose is attached. Backflow devices must be correctly installed to assure their proper operation and maintenance. Backflow devices must be installed on all faucets or hose bibs where a hose can be attached, on soap and other chemical dispensing systems that are plumbed to the buildings water systems, on water lines to dish machines and in soft drink carbonator systems. To prevent the possibility of sewage contacting food or backing up into fixtures such as food preparation sinks, warewashing sinks, ice bins, refrigerators or dishmachines, the drainage systems from these fixtures must drain through an “air break” before entering the sewer. This physical gap in the drain line does not allow waste water to back up into fixtures if a sewage back up should occur.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

Jun 18, 2012

FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
PEST CONTROL
7b Inappropriate pesticide application
PUBLIC HEALTH SIGNIFICANCE
Effective and approved measures must be taken to control insect, rodents, and other pests that may get into food establishments. Effective pest management includes: a) preventing entry of pests into the establishment by providing tight fitting doors and threshold, keeping outside door closed, and sealing off any cracks or openings in foundations or around utility penetrations. b) Depriving them of food, water and shelter by keeping the premises clean, free of the acclimation of refuse, garbage and food spills. c) Kill what gets in with the use of traps or pesticides. Only approved pesticides, registered for application in food establishments can be applied. All pesticides must be used according to label directions. Rodent baits must be contained and dispensed form closed, tamper proof bait stations. The use of open bait stations or tracking powder pesticides can result in the pesticides being dispersed throughout the food establishment and ultimately contaminating food and food contact surfaces.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.
PHYSICAL FACILITIES
14b Garbage and refuse accumulation/uncovered
PUBLIC HEALTH SIGNIFICANCE
The proper storage and disposal of garbage and refuse is necessary to minimize insect, rodent and odor problems. Improperly handled garbage and refuse creates nuisance conditions, makes housekeeping difficult and can result in the contamination of food, equipment and utensils. Garbage and refuse is to be removed form the food establishment daily. It is to be stored in clean, covered, leak proof trash cans, dumpsters or compactors that prevent the scattering of the garbage and refuse by birds. Garbage and refuse must not attract, or harbor or act as a breeding place for flies and rodents. Recyclable materials must be handled in the same manner as garbage and refuse so as to minimize orders, insects and rodents. Recyclable materials, garbage and refuse must be removed from the premises at least once a week.
The proper storage of recyclable materials, garbage and refuse is necessary to minimize insect, rodent and odor problems. Trash dumpster, compactors must be located on concrete or rolled asphalt pads to provide a surface that can be easily cleaned, and that inhibits the breeding of flies and rodents. Floors, walls and ceilings of recycling rooms must be constructed of smooth, durable, non-absorbent materials to facilitate easy cleaning.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.

Do you have any questions you'd like to ask about RICO POLLO 1? Post them here so others can see them and respond.

×

Your question (will be displayed publicly)Your answer (will be displayed publicly)

Name

Email

Show my email publicly

notifytoemail

Do some math: 750 + 9999 =

Submit

Recently added reviews

Create your own business profile on city-data.com. It's completely free!

1. Colorado small cities
2. Colorado smaller cities
3. Colorado
4. Denver County, CO Restaurants