1. Colorado small cities
2. Colorado smaller cities
3. Colorado
4. Denver County, CO Restaurants

Business Info

Restaurant: RUSSELL'S #221
Address: 1200 17th St, Denver, CO
Total inspections: 14
Last inspection: Dec 14, 2010

Score
(the higher the better)
100

Add photo of this business × Description:

Restaurant representatives - add corrected or new information about RUSSELL'S #221, 1200 17th St, Denver, CO »

First Name:

Last Name:

Your position at this restaurant:

E-mail (will not be displayed publicly)   

Phone: (will not be displayed publicly)

Corrected or new information:  (50-4000 characters, will be displayed publicly)

Type the code shown:

Your IP address 52.14.88.137 will be logged.

Violation descriptions and comments

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD TEMPERATURE CONTROL
3f Food thermometer not available
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Because food temperature control is so critical in assuring food safety all foods establishment must have and must use an accurate thermometer to check food temperatures. Food product thermometers are to be scaled 0—220oF. They must be accurate to +/-2oF. Food workers need to verify that foods are being properly cooled, that they are reheated to 165oF, that they are cooked to the required temperatures, that they are held hot above 140oF, etc. by using a thermometer.
FOOD TEMPERATURE CONTROL
3g Equipment inadequate to maintain food temperatures
PUBLIC HEALTH SIGNIFICANCE
The ability of equipment to cool, heat, and hold potentially hazardous foods at required temperatures is critical to food safety. Improper holding and cooking temperatures continue to be major contributing factors to foodborne illness. Therefore, it is very important to have adequate cooking, hot and cold holding equipment with enough capacity to meet the heating and cooling demands of the establishment.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.
UTENSILS - SINGLE SERVICE ARTICLES
13b Single service articles improperly stored, dispensed, used
PUBLIC HEALTH SIGNIFICANCE
Single service items such as paper cups, napkins, straws, plastic “to-go” food containers and plastic tableware must be stored and dispensed in a manner that protects these items from contamination. Single service items must be stored up off the floor. Dispensers can be used to protect these items when in service. Single service items such as tableware may be prewrapped, or provided in a dispenser that presents the utensil handle to the server or consumer.

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD TEMPERATURE CONTROL
3g Equipment inadequate to maintain food temperatures
PUBLIC HEALTH SIGNIFICANCE
The ability of equipment to cool, heat, and hold potentially hazardous foods at required temperatures is critical to food safety. Improper holding and cooking temperatures continue to be major contributing factors to foodborne illness. Therefore, it is very important to have adequate cooking, hot and cold holding equipment with enough capacity to meet the heating and cooling demands of the establishment.

IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12c Dishwashing operations
PUBLIC HEALTH SIGNIFICANCE
Prior to washing and sanitizing heavy food residue left on equipment and utensils must be removed. This pre-scraping or flushing of equipment and utensils helps keep wash and rinse water clean and improves the results of washing and sanitizing
Warewashing water temperatures are a critical factor effecting how well dishwashing detergents work to remove organic matter from equipment and utensils. If wash water temperatures are too low, dish detergents can not effectively dissolve and remove oils and animal fats from dirty equipment and utensils. Wash and rinse water must be kept clean. Equipment and utensils washed and rinsed in heavily soiled water results in soiled and inadequately sanitized surfaces.
After washing and saintizing, clean equipment and utensils must be allowed to drain and air-dry before they are stacked and put away. Wet surfaces of equipment and utensils provide an environment that may allow for the growth of microorganisms. Drying equipment and utensils by hand is prohibited. Hand drying of wet equipment and utensils transfers microorganisms from food workers to utensil surfaces. Clean equipment and utensils must be stored off the floor. Pots, pans, glasses must be stored inverted to help protect them from contamination.

SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
TESTING DEVICES
11c Chemical test kits not provided; inaccessible
PUBLIC HEALTH SIGNIFICANCE
The temperature of the wash and rinse water is a critical factor effecting cleaning and sanitizing of equipment and utensils. It is important that warewashing machines and high-temperature three-compartment warewashing sinks are therefore equipped with accurate thermometers to measure water temperatures. Sanitzer test kits must also be provided and used by food workers to ensure that the concentration of any chemical sanitizers being used are correct. Warewashing machines are required to operate at specific water flow pressures. Water flow pressure can greatly effect how well a dishmachine will sanitize. Low water flow pressure results in inadequate spray patterns and incomplete coverage of the equipment and utensils being washed. Excessive flow pressures will atomize water droplets and again result in incomplete coverage. A pressure gauge installed on the dishmachine’s final rinse line allows workers to monitor the water flow pressure of a dishmachine.

FOOD TEMPERATURE CONTROL
3g Equipment inadequate to maintain food temperatures
PUBLIC HEALTH SIGNIFICANCE
The ability of equipment to cool, heat, and hold potentially hazardous foods at required temperatures is critical to food safety. Improper holding and cooking temperatures continue to be major contributing factors to foodborne illness. Therefore, it is very important to have adequate cooking, hot and cold holding equipment with enough capacity to meet the heating and cooling demands of the establishment.
SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.

SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
TOXIC ITEMS
8c Improperly used
PUBLIC HEALTH SIGNIFICANCE
Failure to use cleaners, sanitizers, and other chemicals properly can be very dangerous. Directions listed on container labels must be followed correctly. Failure to follow stated instructions could result in injury to workers or customers. Sanitizers must be used at the proper concentrations: Chlorine 50 ppm, Quaternary Ammonia 200 ppm, and Iodine 12.5 ppm. High levels of sanitizers or soaps can leave harmful residues.

HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.
TOXIC ITEMS
8c Improperly used
PUBLIC HEALTH SIGNIFICANCE
Failure to use cleaners, sanitizers, and other chemicals properly can be very dangerous. Directions listed on container labels must be followed correctly. Failure to follow stated instructions could result in injury to workers or customers. Sanitizers must be used at the proper concentrations: Chlorine 50 ppm, Quaternary Ammonia 200 ppm, and Iodine 12.5 ppm. High levels of sanitizers or soaps can leave harmful residues.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
TESTING DEVICES
11c Chemical test kits not provided; inaccessible
PUBLIC HEALTH SIGNIFICANCE
The temperature of the wash and rinse water is a critical factor effecting cleaning and sanitizing of equipment and utensils. It is important that warewashing machines and high-temperature three-compartment warewashing sinks are therefore equipped with accurate thermometers to measure water temperatures. Sanitzer test kits must also be provided and used by food workers to ensure that the concentration of any chemical sanitizers being used are correct. Warewashing machines are required to operate at specific water flow pressures. Water flow pressure can greatly effect how well a dishmachine will sanitize. Low water flow pressure results in inadequate spray patterns and incomplete coverage of the equipment and utensils being washed. Excessive flow pressures will atomize water droplets and again result in incomplete coverage. A pressure gauge installed on the dishmachine’s final rinse line allows workers to monitor the water flow pressure of a dishmachine.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD TEMPERATURE CONTROL
3g Equipment inadequate to maintain food temperatures
PUBLIC HEALTH SIGNIFICANCE
The ability of equipment to cool, heat, and hold potentially hazardous foods at required temperatures is critical to food safety. Improper holding and cooking temperatures continue to be major contributing factors to foodborne illness. Therefore, it is very important to have adequate cooking, hot and cold holding equipment with enough capacity to meet the heating and cooling demands of the establishment.
HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD TEMPERATURE CONTROL
3g Equipment inadequate to maintain food temperatures
PUBLIC HEALTH SIGNIFICANCE
The ability of equipment to cool, heat, and hold potentially hazardous foods at required temperatures is critical to food safety. Improper holding and cooking temperatures continue to be major contributing factors to foodborne illness. Therefore, it is very important to have adequate cooking, hot and cold holding equipment with enough capacity to meet the heating and cooling demands of the establishment.

PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

FOOD TEMPERATURE CONTROL
3f Food thermometer not available
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Because food temperature control is so critical in assuring food safety all foods establishment must have and must use an accurate thermometer to check food temperatures. Food product thermometers are to be scaled 0—220oF. They must be accurate to +/-2oF. Food workers need to verify that foods are being properly cooled, that they are reheated to 165oF, that they are cooked to the required temperatures, that they are held hot above 140oF, etc. by using a thermometer.
HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Write your review!

Your Ratings

You can rate this restaurant in different categories from 1 star (worst) to 5 stars (best) or leave category unrated

Food:
Service:
Price:
Ambience:
Cleanliness:

Your Review

Please note that defamatory statements might be against the law. As soon as you visit any website, your IP address is available to that site.

Would you recommend RUSSELL'S #221 to others? (optional)

Yes

  

No

Add photo of RUSSELL'S #221 (optional)

Add more info about the restaurant »

Takes reservations:

Yes No

Accepts credit cards:

Yes No

Parking:

Garage Private Lot Street Valet Validated

Attire:

Casual Dress Business Casual Jacket Preferred Jacket Required Jacket and Tie Required Formal Attire

Good for groups:

Yes No

Good for kids:

Yes No

Delivery:

Yes No

Take-out:

Yes No

Waiter service:

Yes No

Outdoor seating:

Yes No

Wi-Fi:

Yes No

Good for:

Breakfast Brunch Lunch Dessert Dinner Late Night

Alcohol:

Beer & Wine Only Full Bar Happy Hour

Noise level:

Quiet Average Loud

Ambience:

Casual Classy Dive-y Hipster Intimate Romantic Touristy Trendy Upscale

Has TV:

Yes No

Caters:

Yes No

Wheelchair accessible:

Yes No

Live music:

Yes No

Scenic view:

Yes No

Gluten-free friendly:

Yes No

Vegan friendly:

Yes No

Cuisines:

Afghan African American Argentinian Asian Austrian Bagels Bakery Barbecue Bolivian Brazilian Breakfast & Brunch Buffet Burgers Cajun & Creole California Caribbean Chicken Chilean Chinese Coffee Colombian Cuban Delicatessen Desserts & Ice Cream Dim Sum Diner Dominican Donuts Eastern European Ecuadorian El Salvadoran English & Irish Ethiopian & Eritrean European Fast Food Filipino Floribbean French Frozen Yogurt Gastropub German Greek Guatemalan Hawaiian Honduran Hot Dogs & Sausages Indian Indonesian International Italian Jamaican Japanese Korean Kosher Latin American Mediterranean Mexican Middle Eastern Modern American Moroccan Nicaraguan Noodle Shop Nuevo Latino Organic Pakistani Peruvian Pizza Portuguese Pub Food Puerto Rican Russian Salad Sandwiches & Subs Seafood Smoothies Soup Southern & Soul Southwestern Spanish Steakhouse Sushi Tacos Tapas Tea Teriyaki Tex-Mex Thai Turkish Uruguayan Vegetarian Venezuelan Vietnamese Wine Bar

About You

Your nickname:
I have read, and agree to the Terms of Service

Optional Verification

(additional info to increase the weight and the placement of your review and ratings)

	Log in»  |   Register - it's free and very quick!
Real Name:
Email (won't be published):
Date and time of your visit to this restaurant:
Phone number (won't be published):
	Show my IP address (52.14.88.xxx) to everybody
	Leave your signature» Clear Make my signature public

Send Review!

Recently added reviews

Name	City	Users' Rating
LITTLE MISS LATTE #3	Denver, CO
Pho Saigon 66	Denver, CO
Piper Inn	Denver, CO
Karelys Bar	Denver, CO
Roberto Gomez Pizza and Burritos	Denver, CO
Gomez Burritos	Denver, CO
ANTHONY'S PIZZA & PASTA	Denver, CO
7 - ELEVEN	Denver, CO
A MART STORE	Denver, CO
BOSTON MARKET	Denver, CO

1. Colorado small cities
2. Colorado smaller cities
3. Colorado
4. Denver County, CO Restaurants