| No violation noted during this evaluation. | 01/21/2016 | VCR |
- (A) Except as specified in (B) of this section, light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed FOOD; clean EQUIPMENT, UTENSILS, and LINENS; or unwrapped SINGLE-SERVICE and SINGLE-USE ARTICLES. (B) Shielded, coated, or otherwise shatter-resistant bulbs need not be used in areas used only for storing FOOD in unopened packages, if: (1) The integrity of the packages cannot be affected by broken glass falling onto them; and (2) The packages are capable of being cleaned of debris from broken bulbs before the packages are opened. (C) An infrared or other heat lamp shall be protected against breakage by a shield surrounding and extending beyond the bulb so that only the face of the bulb is exposed.
|
01/15/2016 | Routine |
| No violation noted during this evaluation. | 01/15/2016 | Routine |
| No violation noted during this evaluation. | 03/31/2015 | Routine |
| No violation noted during this evaluation. | 03/31/2015 | Routine |
| No violation noted during this evaluation. | 02/10/2014 | VCR |
- Critical: Packaged and Unpackaged Food - Food shall be protected from cross contamination according to the Food Code.
- Temperature Measuring Devices - (A) In a mechanically refrigerated or hot food storage unit, the sensor of a temperature measuring device shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot food storage unit. (B) Except as specified in (C) of this section, cold or hot holding equipment used for potentially hazardous food shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated food transport containers, and salad bars. (D) Temperature measuring devices shall be designed to be easily readable. (E) Food temperature measuring device and water temperature measuring device on warewashing machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1C or 2F in the intended range of use.
- Critical: PHF, Cold Holding - Potentially hazardous cold food shall be maintained at temperatures in accordance with the Food Code. (corrected on site)
- Critical: Controlling Pests - The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by using methods outlined in the Food Code. (corrected on site)
|
01/30/2014 | Routine |
- Critical: Controlling Pests - The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by using methods outlined in the Food Code. (corrected on site)
|
01/30/2014 | Routine |
| No violation noted during this evaluation. | 05/02/2013 | VCR |
- Temperature Measuring Devices - (A) In a mechanically refrigerated or hot food storage unit, the sensor of a temperature measuring device shall be located to measure the air temperature or a simulated product temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot food storage unit. (B) Except as specified in (C) of this section, cold or hot holding equipment used for potentially hazardous food shall be designed to include and shall be equipped with at least one integral or permanently affixed temperature measuring device that is located to allow easy viewing of the device's temperature display. (C) Paragraph (B) of this section does not apply to equipment for which the placement of a temperature measuring device is not a practical means for measuring the ambient air surrounding the food because of the design, type, and use of the equipment, such as calrod units, heat lamps, cold plates, bainmaries, steam tables, insulated food transport containers, and salad bars. (D) Temperature measuring devices shall be designed to be easily readable. (E) Food temperature measuring device and water temperature measuring device on warewashing machines shall have a numerical scale, printed record, or digital readout in increments no greater than 1C or 2F in the intended range of use.
- Critical: PHF, Cold Holding - Potentially hazardous cold food shall be maintained at temperatures in accordance with the Food Code.
- Sanitizing Solutions, Testing Devices - A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided.
|
04/17/2013 | Routine |
| No violation noted during this evaluation. | 04/17/2013 | Routine |
| No violation noted during this evaluation. | 10/02/2012 | Enforcement |
- The physical facilities shall be cleaned as often as necessary to keep them clean; Cleaning shall be done during periods when the least amount of food is exposed such as after closing. This requirement does not apply to cleaning that is necessary due to a spill or other accident.
- Critical: Conveying Sewage - Sewage shall be conveyed to the point of disposal through an approved sanitary sewage system or other system, including use of sewage transport vehicles, waste retention tanks, pumps, pipes, hoses, and connections that are constructed, maintained, and operated according to law.
- Miscellaneous Sources of Contamination - Food shall be protected from contamination that may result from a factor or source not specified under Subparts 3-301 - 3-306. (corrected on site)
- Critical: RTE PHF, Disposition - Ready-to-Eat, Potentially Hazardous Food shall be discarded in accordance with the Food Code. (corrected on site)
- Critical: Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils - Equipment food-contact surfaces and utensils chall be clean to sight and touch. (corrected on site)
- Sanitizing Solutions, Testing Devices - A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided.
|
09/24/2012 | Complaint |
| No violation noted during this evaluation. | 03/29/2012 | VCR |
- Critical: Equipment, Food-Contact Surfaces, Nonfood-Contact Surfaces, and Utensils - Equipment food-contact surfaces and utensils chall be clean to sight and touch. (corrected on site)
- Critical: Demonstration - The Person in Charge shall demonstrate to the Regulatory Authority knowledge of food borne disease prevention, application of the HACCP principles, and the requirements of the Idaho Food Code (IFC). The Person in Charge shall demonstrate this knowledge by at least One of the following: A. Complying with IFC by not having any critical violations at the time of inspection. B. Being a certified food protection manager who has shown proficiency of required information through passing a test that is part of an Accredited Program. The approved programs in Idaho are: Certified Professional Food Manager (CPFM), National Registry of Food Service Professionals (NRFSP), ServSafe, Idaho online course, and the University of Idaho Extension course. C. Responding correctly to the inspector’s questions as they relate to the specific food operation.
- Critical: RTE PHF, Date Marking - Refrigerated, ready-to-eat, potentially hazardous food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, in accordance with the Food Code.
|
03/07/2012 | Routine |
| No violation noted during this evaluation. | 03/07/2012 | Routine |
| No violation noted during this evaluation. | 03/09/2011 | Routine |
| No violation noted during this evaluation. | 03/09/2011 | Routine |
Restaurant representatives - add corrected or new information about Curry Junction, 21313 Hwy 30, Filer, ID 83328 »