1. Colorado small cities
2. Colorado smaller cities
3. Colorado
4. Denver County, CO Restaurants

Violation descriptions and comments

Aug 27, 2000

FOOD SOURCE
1b Unwholesome; signs of spoilage
PUBLIC HEALTH SIGNIFICANCE
Canned or hermetically sealed foods must be handled so as to maintain container and product integrity. Dented and damaged containers allow for the contamination of the food within the container. This contamination can result in the growth of disease-causing bacteria or spoilage of the can’s contents. Food establishments are required to inspect can goods for damage. Damaged goods are not to be used. They must be disposed of or be segregated and held in designated areas pending proper disposition.
FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Non-food contact surfaces of equipment routinely exposed to splash or food debris must be constructed to be smooth, durable, nonabsorbent and easily cleanable. Equipment that does not meet these criteria becomes difficult to clean, allowing soil, moisture, debris and disease-causing bacteria to accumulate.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

Dec 26, 2000

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.
TESTING DEVICES
11c Chemical test kits not provided; inaccessible
PUBLIC HEALTH SIGNIFICANCE
The temperature of the wash and rinse water is a critical factor effecting cleaning and sanitizing of equipment and utensils. It is important that warewashing machines and high-temperature three-compartment warewashing sinks are therefore equipped with accurate thermometers to measure water temperatures. Sanitzer test kits must also be provided and used by food workers to ensure that the concentration of any chemical sanitizers being used are correct. Warewashing machines are required to operate at specific water flow pressures. Water flow pressure can greatly effect how well a dishmachine will sanitize. Low water flow pressure results in inadequate spray patterns and incomplete coverage of the equipment and utensils being washed. Excessive flow pressures will atomize water droplets and again result in incomplete coverage. A pressure gauge installed on the dishmachine’s final rinse line allows workers to monitor the water flow pressure of a dishmachine.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Apr 11, 2001

PERSONNEL
2f Training needed
PUBLIC HEALTH SIGNIFICANCE
Food workers must have a basic understanding of food safety as it relates to the job or task they are doing. Dishwashers must know how the dishmachine they operate sanitizes and when they should be washing their hands. Cooks that reheat foods must know the temperature requirements for reheating. Employees who are required to cool foods must know what the temperature requirements are for cooling. The more knowledgeable the food handler is, the safer the food handling practices in the establishment should be.
FOOD TEMPERATURE CONTROL
3a Rapidly cool food to 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time.
Health Department inspections stress temperature control of potentially hazardous food.Proper cooling means lowering the temperature of the food quickly enough to prevent bacterial growth. Taking too long to cool off cooked foods is a frequent cause of foodborne illness. During lengthy cooling, disease-causing bacteria may grow in potentially hazardous foods. Avoid letting food stay for long periods of time at growth-promoting temperatures for bacteria 70�° F - 120�° F. If the food isn't cooled from 140�° F to 70�° F in two hours or less, then from 70�° F to 41�° F in four hours or less, enough bacteria may grow to cause a foodborne illness.
Restaurants are required to cool food within time frames based on how fast bacteria grow if food becomes recontaminated. By meeting these cooling time expectations, disease-causing bacteria won't grow to dangerous levels even if sanitation is less than ideal.
FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
SANITATION RINSE
4c In place
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
Establishments will often have equipment that needs to be washed and sanitized, but is too large to fit into warewashing sinks or dishmachines, or is not designed to be submerged in water. This equipment must be washed and sanitized “in place”. Surfaces must be washed with a detergent solution to remove food residue, then rinsed free of detergents with clean water and then sanitized with an approved sanitizer.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.

Sep 28, 2001

FOOD SOURCE
1b Unwholesome; signs of spoilage
PUBLIC HEALTH SIGNIFICANCE
Canned or hermetically sealed foods must be handled so as to maintain container and product integrity. Dented and damaged containers allow for the contamination of the food within the container. This contamination can result in the growth of disease-causing bacteria or spoilage of the can’s contents. Food establishments are required to inspect can goods for damage. Damaged goods are not to be used. They must be disposed of or be segregated and held in designated areas pending proper disposition.
FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.

Jan 28, 2002

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.

Apr 25, 2002

TESTING DEVICES
11a Refrigeration units not provided with accurate, conspicuous thermometer
PUBLIC HEALTH SIGNIFICANCE
Conspicuous thermometers are required in all refrigeration units and hot food holding cabinets where potentially hazardous foods are stored. Maintaining foods at safe temperatures is critical in controlling the growth of disease-causing bacteria. Should the temperature of a refrigerator exceed 41oF or a hot holding cabinet be less than 140oF, bacterial growth can occur. In order to facilitate the routine monitoring of equipment temperatures, clearly visible thermometers must be provided in all refrigerations and hot holding cabinets and must be routinely checked by food establishment personnel.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.
PHYSICAL FACILITIES
14e Ventilation inadequate
PUBLIC HEALTH SIGNIFICANCE
Adequate ventilation is very important in maintaining a high level of sanitation in a food establishment. A poorly ventilated kitchen is generally very hot and can contribute to refrigeration not being capable of holding foods at less than 410F. Insect and rodent infestations may occur if doors and windows are left open in an attempt to cool the establishment. Worker hygiene may be effected by sweat dripping into food or onto food contact surfaces, or by contaminating hands when wiping the face. Soiling of walls, ceilings and equipment surfaces with smoke, grease and moisture may also result. Make-up air and exhaust systems may require more frequent repairs. Carbon monoxide can reach dangerous levels if back draft of gas appliances such as water heaters, occurs as a result of inadequate ventilation.

Aug 24, 2002

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Non-food contact surfaces of equipment routinely exposed to splash or food debris must be constructed to be smooth, durable, nonabsorbent and easily cleanable. Equipment that does not meet these criteria becomes difficult to clean, allowing soil, moisture, debris and disease-causing bacteria to accumulate.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.
PHYSICAL FACILITIES
14a Plumbing not installed/maintained
PUBLIC HEALTH SIGNIFICANCE
It is critical that all plumbing fixtures, water and sewer lines in food establishments be maintained in proper working order. Poorly maintained plumbing systems may result in potential heath hazard such as cross connections, the back up of sewage, or leakage. These conditions may directly result in the contamination of food, equipment, utensils or paper goods. They can also adversely affect the ability of food handlers to adequately wash their hands, an establishment’s warewashing operations and increase the potential for cross contamination of food and equipment and utensil.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Jan 4, 2003

IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Non-food contact surfaces of equipment routinely exposed to splash or food debris must be constructed to be smooth, durable, nonabsorbent and easily cleanable. Equipment that does not meet these criteria becomes difficult to clean, allowing soil, moisture, debris and disease-causing bacteria to accumulate.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

May 3, 2003

FOOD SOURCE
1a Unapproved source
PUBLIC HEALTH SIGNIFICANCE
All foods used in retail food establishments must be obtained from commercial suppliers that are inspected by health authorities (state or local health departments, USDA, FDA). Foods prepared in private homes are frequently implicated in foodborne outbreaks. Non-commercial kitchens have limited capacity for maintaining food at proper temperatures and due to their small size are conducive to situations that can result in cross contamination. Controlled processing is required for the safe preparation of food for sale to the public.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Non-food contact surfaces of equipment routinely exposed to splash or food debris must be constructed to be smooth, durable, nonabsorbent and easily cleanable. Equipment that does not meet these criteria becomes difficult to clean, allowing soil, moisture, debris and disease-causing bacteria to accumulate.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Sep 10, 2003

PERSONNEL
2e Smoking; eating; drinking not restricted
PUBLIC HEALTH SIGNIFICANCE
The use of tobacco products or eating or drinking during food preparation is prohibited. The hand to mouth contact that occurs during these activities results in the contamination of workers hands and food.

Mar 9, 2004

HAND WASHING & TOILET FACILITIES
6b Inaccessible
PUBLIC HEALTH SIGNIFICANCE
Food workers may be unlikely to wash their hands unless properly equipped handwashing sinks are accessible in the immediate work area. Handwashing sinks which are improperly located may be blocked by portable equipment or stacked full of soiled utensils and other items, rendering the sink unavailable for use. Nothing must block the approach to a handwashing sink thereby discouraging its use.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Jul 20, 2004

IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Non-food contact surfaces of equipment routinely exposed to splash or food debris must be constructed to be smooth, durable, nonabsorbent and easily cleanable. Equipment that does not meet these criteria becomes difficult to clean, allowing soil, moisture, debris and disease-causing bacteria to accumulate.

Feb 3, 2005

PERSONNEL
2e Smoking; eating; drinking not restricted
PUBLIC HEALTH SIGNIFICANCE
The use of tobacco products or eating or drinking during food preparation is prohibited. The hand to mouth contact that occurs during these activities results in the contamination of workers hands and food.

Jun 17, 2005

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD TEMPERATURE CONTROL
3f Food thermometer not available
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Because food temperature control is so critical in assuring food safety all foods establishment must have and must use an accurate thermometer to check food temperatures. Food product thermometers are to be scaled 0—220oF. They must be accurate to +/-2oF. Food workers need to verify that foods are being properly cooled, that they are reheated to 165oF, that they are cooked to the required temperatures, that they are held hot above 140oF, etc. by using a thermometer.
SANITATION RINSE
4b Mechanical
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
If a dishmachine is provided in a food establishment it must be a commercial type that has been shown to effectively sanitize. Most commercial dishmachines sanitize equipment and utensils by the accumulation of heat from contact with 180oF hot water or by contact with chemical sanitizers such as 50 ppm chlorine.
HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.
TESTING DEVICES
11a Refrigeration units not provided with accurate, conspicuous thermometer
PUBLIC HEALTH SIGNIFICANCE
Conspicuous thermometers are required in all refrigeration units and hot food holding cabinets where potentially hazardous foods are stored. Maintaining foods at safe temperatures is critical in controlling the growth of disease-causing bacteria. Should the temperature of a refrigerator exceed 41oF or a hot holding cabinet be less than 140oF, bacterial growth can occur. In order to facilitate the routine monitoring of equipment temperatures, clearly visible thermometers must be provided in all refrigerations and hot holding cabinets and must be routinely checked by food establishment personnel.
TESTING DEVICES
11c Chemical test kits not provided; inaccessible
PUBLIC HEALTH SIGNIFICANCE
The temperature of the wash and rinse water is a critical factor effecting cleaning and sanitizing of equipment and utensils. It is important that warewashing machines and high-temperature three-compartment warewashing sinks are therefore equipped with accurate thermometers to measure water temperatures. Sanitzer test kits must also be provided and used by food workers to ensure that the concentration of any chemical sanitizers being used are correct. Warewashing machines are required to operate at specific water flow pressures. Water flow pressure can greatly effect how well a dishmachine will sanitize. Low water flow pressure results in inadequate spray patterns and incomplete coverage of the equipment and utensils being washed. Excessive flow pressures will atomize water droplets and again result in incomplete coverage. A pressure gauge installed on the dishmachine’s final rinse line allows workers to monitor the water flow pressure of a dishmachine.

Dec 7, 2005

FOOD TEMPERATURE CONTROL
3a Rapidly cool food to 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time.
Health Department inspections stress temperature control of potentially hazardous food.Proper cooling means lowering the temperature of the food quickly enough to prevent bacterial growth. Taking too long to cool off cooked foods is a frequent cause of foodborne illness. During lengthy cooling, disease-causing bacteria may grow in potentially hazardous foods. Avoid letting food stay for long periods of time at growth-promoting temperatures for bacteria 70�° F - 120�° F. If the food isn't cooled from 140�° F to 70�° F in two hours or less, then from 70�° F to 41�° F in four hours or less, enough bacteria may grow to cause a foodborne illness.
Restaurants are required to cool food within time frames based on how fast bacteria grow if food becomes recontaminated. By meeting these cooling time expectations, disease-causing bacteria won't grow to dangerous levels even if sanitation is less than ideal.
WATER * SEWAGE * PLUMBING SYSTEMS
5b Hot & cold water inadequate
PUBLIC HEALTH SIGNIFICANCE
The availability of sufficient, safe water is a basic requirement for proper sanitation within a food establishment. All water supplied to food establishments, either from public systems or private wells, must meet the requirements of the Colorado Primary Drinking Water Regulations. A sufficient supply of hot water is critical for employee hand washing, washing of equipment and utensils, and general cleaning needed in all food establishments.
HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Food contact surfaces of equipment and utensils must be designed and constructed to be smooth, durable, non-absorbant and easily cleanable. These surfaces must also be constructed of safe materials that will not impart toxic substances into the food when foods are in contact with these surfaces. Equipment that is of poor design and construction does not allow for easy cleaning and will result in the accumulation of soal and the contamination of the food that comes into contact with it.
TESTING DEVICES
11c Chemical test kits not provided; inaccessible
PUBLIC HEALTH SIGNIFICANCE
The temperature of the wash and rinse water is a critical factor effecting cleaning and sanitizing of equipment and utensils. It is important that warewashing machines and high-temperature three-compartment warewashing sinks are therefore equipped with accurate thermometers to measure water temperatures. Sanitzer test kits must also be provided and used by food workers to ensure that the concentration of any chemical sanitizers being used are correct. Warewashing machines are required to operate at specific water flow pressures. Water flow pressure can greatly effect how well a dishmachine will sanitize. Low water flow pressure results in inadequate spray patterns and incomplete coverage of the equipment and utensils being washed. Excessive flow pressures will atomize water droplets and again result in incomplete coverage. A pressure gauge installed on the dishmachine’s final rinse line allows workers to monitor the water flow pressure of a dishmachine.

Mar 30, 2006

SANITATION RINSE
4b Mechanical
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
If a dishmachine is provided in a food establishment it must be a commercial type that has been shown to effectively sanitize. Most commercial dishmachines sanitize equipment and utensils by the accumulation of heat from contact with 180oF hot water or by contact with chemical sanitizers such as 50 ppm chlorine.
IMPROPER EQUIPMENT DESIGN AND CONSTRUCTION
10b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Non-food contact surfaces of equipment routinely exposed to splash or food debris must be constructed to be smooth, durable, nonabsorbent and easily cleanable. Equipment that does not meet these criteria becomes difficult to clean, allowing soil, moisture, debris and disease-causing bacteria to accumulate.

Apr 5, 2006

HAND WASHING & TOILET FACILITIES
6a Inadequate in number, location, and design
PUBLIC HEALTH SIGNIFICANCE
Because handwashing is such an important factor in the prevention of foodborne illness, sufficient handwashing sinks must be available to make handwashing not only possible, but likely.

Apr 26, 2006

HAND WASHING & TOILET FACILITIES
6a Inadequate in number, location, and design
PUBLIC HEALTH SIGNIFICANCE
Because handwashing is such an important factor in the prevention of foodborne illness, sufficient handwashing sinks must be available to make handwashing not only possible, but likely.

May 11, 2006

HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.

Aug 7, 2006

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD TEMPERATURE CONTROL
3g Equipment inadequate to maintain food temperatures
PUBLIC HEALTH SIGNIFICANCE
The ability of equipment to cool, heat, and hold potentially hazardous foods at required temperatures is critical to food safety. Improper holding and cooking temperatures continue to be major contributing factors to foodborne illness. Therefore, it is very important to have adequate cooking, hot and cold holding equipment with enough capacity to meet the heating and cooling demands of the establishment.
PHYSICAL FACILITIES
14e Ventilation inadequate
PUBLIC HEALTH SIGNIFICANCE
Adequate ventilation is very important in maintaining a high level of sanitation in a food establishment. A poorly ventilated kitchen is generally very hot and can contribute to refrigeration not being capable of holding foods at less than 410F. Insect and rodent infestations may occur if doors and windows are left open in an attempt to cool the establishment. Worker hygiene may be effected by sweat dripping into food or onto food contact surfaces, or by contaminating hands when wiping the face. Soiling of walls, ceilings and equipment surfaces with smoke, grease and moisture may also result. Make-up air and exhaust systems may require more frequent repairs. Carbon monoxide can reach dangerous levels if back draft of gas appliances such as water heaters, occurs as a result of inadequate ventilation.

Feb 1, 2007

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
HAND WASHING & TOILET FACILITIES
6b Inaccessible
PUBLIC HEALTH SIGNIFICANCE
Food workers may be unlikely to wash their hands unless properly equipped handwashing sinks are accessible in the immediate work area. Handwashing sinks which are improperly located may be blocked by portable equipment or stacked full of soiled utensils and other items, rendering the sink unavailable for use. Nothing must block the approach to a handwashing sink thereby discouraging its use.
HAND WASHING & TOILET FACILITIES
6c Soap and drying devices unavailable
PUBLIC HEALTH SIGNIFICANCE
Handwashing sinks must be kept clean and well stocked with hand soap and hand towels to encourage frequent use. Hot and cold water must be provided through a mixing valve so employees can properly wash their hands.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.

Jul 23, 2007

IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

Nov 17, 2007

PERSONNEL
2d Poor hygienic practices
PUBLIC HEALTH SIGNIFICANCE
Retail food establishments must have a Health Department approved Hazard Analysis Critical Control Point (HACCP) plan in place when vacuum packageing or when conducting other forms of modified oxygen packaging (MAP). Foods not properly processed using MAP techniques are prone to the growth of botulism. All MAP processed foods must be held refrigerated at 41oF or less until cooking or service. Shelf life of MAP foods are not to exceed 10 days.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.
PHYSICAL FACILITIES
14a Plumbing not installed/maintained
PUBLIC HEALTH SIGNIFICANCE
It is critical that all plumbing fixtures, water and sewer lines in food establishments be maintained in proper working order. Poorly maintained plumbing systems may result in potential heath hazard such as cross connections, the back up of sewage, or leakage. These conditions may directly result in the contamination of food, equipment, utensils or paper goods. They can also adversely affect the ability of food handlers to adequately wash their hands, an establishment’s warewashing operations and increase the potential for cross contamination of food and equipment and utensil.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.

Apr 23, 2008

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
SANITATION RINSE
4b Mechanical
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
If a dishmachine is provided in a food establishment it must be a commercial type that has been shown to effectively sanitize. Most commercial dishmachines sanitize equipment and utensils by the accumulation of heat from contact with 180oF hot water or by contact with chemical sanitizers such as 50 ppm chlorine.

Aug 7, 2008

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

Dec 22, 2008

PERSONNEL
2d Poor hygienic practices
PUBLIC HEALTH SIGNIFICANCE
Retail food establishments must have a Health Department approved Hazard Analysis Critical Control Point (HACCP) plan in place when vacuum packageing or when conducting other forms of modified oxygen packaging (MAP). Foods not properly processed using MAP techniques are prone to the growth of botulism. All MAP processed foods must be held refrigerated at 41oF or less until cooking or service. Shelf life of MAP foods are not to exceed 10 days.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
FOOD TEMPERATURE CONTROL
3g Equipment inadequate to maintain food temperatures
PUBLIC HEALTH SIGNIFICANCE
The ability of equipment to cool, heat, and hold potentially hazardous foods at required temperatures is critical to food safety. Improper holding and cooking temperatures continue to be major contributing factors to foodborne illness. Therefore, it is very important to have adequate cooking, hot and cold holding equipment with enough capacity to meet the heating and cooling demands of the establishment.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

May 21, 2009

PERSONNEL
2e Smoking; eating; drinking not restricted
PUBLIC HEALTH SIGNIFICANCE
The use of tobacco products or eating or drinking during food preparation is prohibited. The hand to mouth contact that occurs during these activities results in the contamination of workers hands and food.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
SANITATION RINSE
4b Mechanical
PUBLIC HEALTH SIGNIFICANCE
All equipment, utensils and food contact surfaces must be properly washed and then sanitized to minimize food contamination. Washing is the removal of food residue or soil from surfaces. Sanitization is the application of heat or chemicals on cleaned surfaces that results in a 99.999% reduction of disease-causing microorganisms. There are many different types of sanitizers that can be used in food establishments. The most common include: hot water between 165oF and 180oF, chlorine mixed at a concentration of 50 ppm, quaternary ammonia mixed at a concentration of 200 ppm, and iodine mixed at a concentration of 12.5 ppm.
If a dishmachine is provided in a food establishment it must be a commercial type that has been shown to effectively sanitize. Most commercial dishmachines sanitize equipment and utensils by the accumulation of heat from contact with 180oF hot water or by contact with chemical sanitizers such as 50 ppm chlorine.
PEST CONTROL
7a Evidence of insects or rodents
PUBLIC HEALTH SIGNIFICANCE
Rodents such as mice and rats live in and feed on garbage and refuse. Disease-causing microorganisms are therefore often present on their hair, in their feces and urine. Microorganisms can be transmitted to people when rodents come into contact and contaminate food and food contact surfaces.
Flies breed in and feed on garbage, refuse and sewage. Disease-causing microorganisms are therefore often present on their body hairs and mouth parts. Microorganisms can be transmitted to people when flies land on and contaminate food and utensils.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.
UTENSILS - SINGLE SERVICE ARTICLES
13a Utensils not provided; used/stored improperly
PUBLIC HEALTH SIGNIFICANCE
To help prevent contamination of food by workers, utensils must be provided and used to dispense food. Utensils must also be provided for use in all customer self service areas such as salad bars, buffets and for bulk food dispensing.
Utensils that are provided to dispense and serve foods must be stored and handled in a manner that protects the utensil and the food from contamination. Contaminated utensils will contaminate the foods that are being dispensed and served. To prevent possible contamination of food by utensils during pauses in preparation and dispensing , utensils must be stored:
a) in the food with the handle up out of the food,
b) in a running water dipper well,
c) in ice
water or in hot water that is above 140oF,
d) on a clean dry surface if the utensil is cleaned and sanitized once every four hours.
PHYSICAL FACILITIES
14c Floors; walls; ceilings in disrepair
PUBLIC HEALTH SIGNIFICANCE
Floors must be kept clean, free of any build up of food spills, dirt and refuse. The accumulation of soil on floors increases the potential for contamination of food, equipment and utensils. It also provides food and harborage for rodents and insects, such as flies and cockroaches. To facilitate easy cleaning, floors must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Floor-wall junctures must be tightly coved with concave cove base to prevent moisture and food residue from collecting in corners and along walls. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture penetrating into or through the floor.
Walls and ceilings must be kept clean and free of any build up of food spills, splash or dirt. The accumulation of soil on walls and ceilings increases the potential for contamination of food, equipment and utensils. It also provides a food source for rodents, insects, such as flies and cockroaches. To facilitate easy cleaning, walls and ceilings must be maintained and constructed to be smooth, durable, non-absorbent and easily cleanable. Utilities such as water pipes, sewer lines and electrical conduit are to be enclosed within or behind finished walls and ceilings. Utility penetrations must be sealed to eliminate insect and rodent harborage and to prevent moisture from penetrating into walls and ceilings. Exposed utility lines make cleaning difficult.

Aug 30, 2010

PERSONNEL
2e Smoking; eating; drinking not restricted
PUBLIC HEALTH SIGNIFICANCE
The use of tobacco products or eating or drinking during food preparation is prohibited. The hand to mouth contact that occurs during these activities results in the contamination of workers hands and food.
PERSONNEL
2f Training needed
PUBLIC HEALTH SIGNIFICANCE
Food workers must have a basic understanding of food safety as it relates to the job or task they are doing. Dishwashers must know how the dishmachine they operate sanitizes and when they should be washing their hands. Cooks that reheat foods must know the temperature requirements for reheating. Employees who are required to cool foods must know what the temperature requirements are for cooling. The more knowledgeable the food handler is, the safer the food handling practices in the establishment should be.
PEST CONTROL
7a Evidence of insects or rodents
PUBLIC HEALTH SIGNIFICANCE
Rodents such as mice and rats live in and feed on garbage and refuse. Disease-causing microorganisms are therefore often present on their hair, in their feces and urine. Microorganisms can be transmitted to people when rodents come into contact and contaminate food and food contact surfaces.
Flies breed in and feed on garbage, refuse and sewage. Disease-causing microorganisms are therefore often present on their body hairs and mouth parts. Microorganisms can be transmitted to people when flies land on and contaminate food and utensils.
FOOD LABELING AND PROTECTION
9b Food unprotected from contamination
PUBLIC HEALTH SIGNIFICANCE
Freezing prevents microbial growth in foods, but usually does not destroy all microorganisms. Improper thawing provides an opportunity for surviving bacteria to grow to harmful numbers. If the food is then refrozen, significant numbers of bacteria may be preserved in the food.
Disease-causing organisms can contaminate and/or grow in food that is not stored properly. Drips from condensation and drafts of unfiltered air can be sources of microbial contamination for stored foods. Shoes carry contamination onto the floors of food preparation and storage areas. Raw meats and poultry can contaminate cooked and ready to eat foods if stored above these ready to eat items. Even trace amounts of refuse or wastes present in toilet rooms, rooms used for dressing, storing garbage or tools, or rooms housing machinery can become sources of food contamination.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
PHYSICAL FACILITIES
14a Plumbing not installed/maintained
PUBLIC HEALTH SIGNIFICANCE
It is critical that all plumbing fixtures, water and sewer lines in food establishments be maintained in proper working order. Poorly maintained plumbing systems may result in potential heath hazard such as cross connections, the back up of sewage, or leakage. These conditions may directly result in the contamination of food, equipment, utensils or paper goods. They can also adversely affect the ability of food handlers to adequately wash their hands, an establishment’s warewashing operations and increase the potential for cross contamination of food and equipment and utensil.
Toilet rooms and facilities must be of sanitary design and kept clean and in good repair to help prevent contamination of food preparation areas, to motivate employees to maintain a high degree of personal hygiene and to use good sanitary practices. Doors to toilet rooms must be kept closed to help prevent the possible spread of disease-causing microorganisms by flies.

Dec 17, 2010

PERSONNEL
2c Hands not washed as needed
PUBLIC HEALTH SIGNIFICANCE
The hands are particularly important in transmitting foodborne disease-causing organisms. Food employees with dirty hands and/or fingernails may contaminate the food being prepared. Therefore, any activity which may contaminate the hands must be followed by thorough handwashing. Even seemingly healthy employees may serve as reservoirs for disease-causing microorganisms that are transmissible through food. Staphylococci bacteria, for example, can be found on the skin and in the mouth, throat, and nose of many healthy employees. The hands of employees can be contaminated by touching their nose, mouth, hair or other body parts.
PERSONNEL
2d Poor hygienic practices
PUBLIC HEALTH SIGNIFICANCE
Retail food establishments must have a Health Department approved Hazard Analysis Critical Control Point (HACCP) plan in place when vacuum packageing or when conducting other forms of modified oxygen packaging (MAP). Foods not properly processed using MAP techniques are prone to the growth of botulism. All MAP processed foods must be held refrigerated at 41oF or less until cooking or service. Shelf life of MAP foods are not to exceed 10 days.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
TESTING DEVICES
11c Chemical test kits not provided; inaccessible
PUBLIC HEALTH SIGNIFICANCE
The temperature of the wash and rinse water is a critical factor effecting cleaning and sanitizing of equipment and utensils. It is important that warewashing machines and high-temperature three-compartment warewashing sinks are therefore equipped with accurate thermometers to measure water temperatures. Sanitzer test kits must also be provided and used by food workers to ensure that the concentration of any chemical sanitizers being used are correct. Warewashing machines are required to operate at specific water flow pressures. Water flow pressure can greatly effect how well a dishmachine will sanitize. Low water flow pressure results in inadequate spray patterns and incomplete coverage of the equipment and utensils being washed. Excessive flow pressures will atomize water droplets and again result in incomplete coverage. A pressure gauge installed on the dishmachine’s final rinse line allows workers to monitor the water flow pressure of a dishmachine.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12a Food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
Microorganisms can get into food by food handlers using dirty utensils, cutting boards, slicers, work counters and other surfaces that directly come into contact with food. Food contact surfaces must be kept clean so they are not a source of food contamination. To prevent bacteria from growing on food contact surfaces they must be cleaned and sanitzed after each use or once every four hours when used in a constant production line bases. During manual warewashing of equipment and utensils, all soaps and abrasive detergents must be rinsed from food contact surfaces so sanitzing agents can be properly applied and be effective.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.
UTENSILS - SINGLE SERVICE ARTICLES
13c Reuse of single service articles
PUBLIC HEALTH SIGNIFICANCE
Single service items such as paper cups, napkins, straws, plastic “to-go” food containers and plastic tableware are to be used once and then discarded. These items are not constructed to be durable enough to withstand repeated use and repeated washing and sanitizing.

Jun 29, 2011

FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
WATER * SEWAGE * PLUMBING SYSTEMS
5b Hot & cold water inadequate
PUBLIC HEALTH SIGNIFICANCE
The availability of sufficient, safe water is a basic requirement for proper sanitation within a food establishment. All water supplied to food establishments, either from public systems or private wells, must meet the requirements of the Colorado Primary Drinking Water Regulations. A sufficient supply of hot water is critical for employee hand washing, washing of equipment and utensils, and general cleaning needed in all food establishments.

Aug 24, 2011

FOOD TEMPERATURE CONTROL
3a Rapidly cool food to 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time.
Health Department inspections stress temperature control of potentially hazardous food.Proper cooling means lowering the temperature of the food quickly enough to prevent bacterial growth. Taking too long to cool off cooked foods is a frequent cause of foodborne illness. During lengthy cooling, disease-causing bacteria may grow in potentially hazardous foods. Avoid letting food stay for long periods of time at growth-promoting temperatures for bacteria 70�° F - 120�° F. If the food isn't cooled from 140�° F to 70�° F in two hours or less, then from 70�° F to 41�° F in four hours or less, enough bacteria may grow to cause a foodborne illness.
Restaurants are required to cool food within time frames based on how fast bacteria grow if food becomes recontaminated. By meeting these cooling time expectations, disease-causing bacteria won't grow to dangerous levels even if sanitation is less than ideal.

Jun 5, 2012

FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.
IMPROPER CLEANING OF EQUIPMENT AND UTENSILS
12b Non-food contact surfaces
PUBLIC HEALTH SIGNIFICANCE
The surfaces of cabinets, utensil drawers, shelves, the outsides surfaces of refrigerators, hot holding equipment and other nonfood contact surfaces must be cleaned to keep them free of accumulation of food spills, dirt and grease. The presence of food debris or dirt on nonfood contact surfaces may provide a suitable environment for the growth of bacteria. Workers may inadvertently transfer this contamination to food. Accumulation of food spills and food residue on nonfood contact surfaces may also be a source of food and harborage of insects, rodents, and other pest.

Aug 29, 2012

FOOD TEMPERATURE CONTROL
3c Hold hot at 135 �°F or greater
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
Bacterial growth and possible toxin production by some bacteria, can occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. Bacterial growth is greatly reduced when food temperatures reach 120oF. It is almost completely inhibited at 140oF.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the Health Department.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.

Dec 17, 2012

FOOD TEMPERATURE CONTROL
3a Rapidly cool food to 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time.
Health Department inspections stress temperature control of potentially hazardous food.Proper cooling means lowering the temperature of the food quickly enough to prevent bacterial growth. Taking too long to cool off cooked foods is a frequent cause of foodborne illness. During lengthy cooling, disease-causing bacteria may grow in potentially hazardous foods. Avoid letting food stay for long periods of time at growth-promoting temperatures for bacteria 70�° F - 120�° F. If the food isn't cooled from 140�° F to 70�° F in two hours or less, then from 70�° F to 41�° F in four hours or less, enough bacteria may grow to cause a foodborne illness.
Restaurants are required to cool food within time frames based on how fast bacteria grow if food becomes recontaminated. By meeting these cooling time expectations, disease-causing bacteria won't grow to dangerous levels even if sanitation is less than ideal.
FOOD TEMPERATURE CONTROL
3e Hold cold at 41 �°F or less
PUBLIC HEALTH SIGNIFICANCE
Most food poisonings are associated with foods held at temperatures between 41oF and 140oF for extended periods of time. Health Department inspections stress temperature control of potentially hazardous food.
The rate of bacterial growth and possible toxin production by some bacteria, can be greatly reduced when foods are held at temperatures of less than 41oF. This cold holding temperature does not generally kill the bacteria that may be present in food, but will slow or inhibit their growth.
Bacterial growth and possible toxin production by some bacteria, will occur in potentially hazardous foods that remain at temperatures between 41oF and 140oF for extended periods of time. If a food is held “off” temperature (between 41oF and 140oF) for only a short time, no significant bacterial growth or toxin production should occur. When time is used to control bacterial growth, potentially hazardous foods can be held off temperature for only four hours or less. After this time any food product that has not been served must be discarded. Operations that use time as a control must develop a plan that outlines food handling procedures, identifies when a food item is removed from temperature control and when it is to be disposed of. This plan must be approved by the health department.

Dec 21, 2012

PERSONNEL
2g Bare hand contact
PUBLIC HEALTH SIGNIFICANCE
Touching ready-to-eat foods (i.e. foods that will not go through a further cooking process prior to serving) with bare hands increases the risk of the spread of foodborne illness. Ready-to-eat foods cannot be handled with bare hands but may be handled with gloved hands, tongs, or other utensils.

Do you have any questions you'd like to ask about HYATT 1876? Post them here so others can see them and respond.

×

Your question (will be displayed publicly)Your answer (will be displayed publicly)

Name

Email

Show my email publicly

notifytoemail

Do some math: 329 + 646 =

Submit

Recently added reviews

Create your own business profile on city-data.com. It's completely free!

1. Colorado small cities
2. Colorado smaller cities
3. Colorado
4. Denver County, CO Restaurants